Mercurial > pihelp
annotate Makefile @ 20:bc48a1d17edf
near done
| author | Matt Johnston <matt@ucc.asn.au> |
|---|---|
| date | Sun, 16 Jun 2013 13:04:09 +0800 |
| parents | 021e6e0006f4 |
| children | a55d7c2440fd |
| rev | line source |
|---|---|
| 0 | 1 # Name: Makefile |
| 2 # Author: <insert your name here> | |
| 3 # Copyright: <insert your copyright message here> | |
| 4 # License: <insert your license reference here> | |
| 5 | |
| 6 # This is a prototype Makefile. Modify it according to your needs. | |
| 7 # You should at least check the settings for | |
| 8 # DEVICE ....... The AVR device you compile for | |
| 20 | 9 # CLOCK ........ Target AVR CLOCK rate in Hertz |
| 0 | 10 # OBJECTS ...... The object files created from your source files. This list is |
| 11 # usually the same as the list of source files with suffix ".o". | |
| 12 # PROGRAMMER ... Options to avrdude which define the hardware you use for | |
| 13 # uploading to the AVR and the interface where this hardware | |
| 14 # is connected. We recommend that you leave it undefined and | |
| 15 # add settings like this to your ~/.avrduderc file: | |
| 16 # default_programmer = "stk500v2" | |
| 17 # default_serial = "avrdoper" | |
| 18 # FUSES ........ Parameters for avrdude to flash the fuses appropriately. | |
| 19 | |
| 20 DEVICE = atmega328 | |
| 21 PROGDEVICE = atmega328p | |
| 20 | 22 CLOCK = 4915200L |
| 0 | 23 PROGRAMMER = #-c stk500v2 -P avrdoper |
| 24 PROGRAMMER = -c stk500 -P ~/dev/stk500 -p $(PROGDEVICE) -B 2 | |
| 25 SOURCE_1WIRE = onewire.c simple_ds18b20.c crc8.c | |
| 5 | 26 SOURCE_CRYPTO = hmac-sha1.c sha1-asm.S aes.c |
| 0 | 27 SOURCE = main.c |
| 2 | 28 SOURCE += $(SOURCE_CRYPTO) |
| 0 | 29 LIBS = -lm |
| 30 | |
| 31 # default but 2mhz | |
|
18
021e6e0006f4
debug printing, 5v adc, fixes
Matt Johnston <matt@ucc.asn.au>
parents:
17
diff
changeset
|
32 FUSES = -U hfuse:w:0xd9:m -U lfuse:w:0x77:m -U efuse:w:0xfd:m |
| 0 | 33 |
| 34 # ATMega8 fuse bits used above (fuse bits for other devices are different!): | |
| 35 # Example for 8 MHz internal oscillator | |
| 36 # Fuse high byte: | |
| 37 # 0xd9 = 1 1 0 1 1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000) | |
| 38 # ^ ^ ^ ^ ^ ^ ^------ BOOTSZ0 | |
| 39 # | | | | | +-------- BOOTSZ1 | |
| 40 # | | | | +---------- EESAVE (set to 0 to preserve EEPROM over chip erase) | |
| 41 # | | | +-------------- WDTON | |
| 42 # | | +---------------- SPIEN (if set to 1, serial programming is disabled) | |
| 43 # | +------------------ DWEN | |
| 44 # +-------------------- RSTDISBL (if set to 0, RESET pin is disabled) | |
| 45 # Fuse low byte: | |
|
18
021e6e0006f4
debug printing, 5v adc, fixes
Matt Johnston <matt@ucc.asn.au>
parents:
17
diff
changeset
|
46 # 0x77 0 1 1 1 0 1 1 1 (low rising, full swing, crystal) |
| 0 | 47 # 0x62 = 0 1 1 0 0 0 1 0 |
| 48 # ^ ^ \ / \--+--/ | |
| 49 # | | | +------- CKSEL 3..0 (8M internal RC) | |
| 50 # | | +--------------- SUT 1..0 (slowly rising power) | |
| 51 # | +------------------ CKOUT | |
|
18
021e6e0006f4
debug printing, 5v adc, fixes
Matt Johnston <matt@ucc.asn.au>
parents:
17
diff
changeset
|
52 # +-------------------- CLKDIV8 (initial) |
|
021e6e0006f4
debug printing, 5v adc, fixes
Matt Johnston <matt@ucc.asn.au>
parents:
17
diff
changeset
|
53 |
|
021e6e0006f4
debug printing, 5v adc, fixes
Matt Johnston <matt@ucc.asn.au>
parents:
17
diff
changeset
|
54 # Extended fuse: |
|
021e6e0006f4
debug printing, 5v adc, fixes
Matt Johnston <matt@ucc.asn.au>
parents:
17
diff
changeset
|
55 # 0xfd = 2.7V BOD |
|
021e6e0006f4
debug printing, 5v adc, fixes
Matt Johnston <matt@ucc.asn.au>
parents:
17
diff
changeset
|
56 # |
| 0 | 57 # |
| 58 # For computing fuse byte values for other devices and options see | |
| 59 # the fuse bit calculator at http://www.engbedded.com/fusecalc/ | |
| 60 | |
| 61 | |
| 62 # Tune the lines below only if you know what you are doing: | |
| 63 | |
| 64 AVRDUDE = avrdude $(PROGRAMMER) | |
| 65 #COMPILE = avr-gcc -Wall -Os -DF_CPU=$(CLOCK) -mmcu=$(DEVICE) -g -std=c99 -mcall-prologues -fdata-sections -ffunction-sections -Wl,--gc-sections -Wl,--relax -fwhole-program -Wl,-u,vfprintf -lprintf_flt -lm | |
| 2 | 66 COMPILE = /usr/local/CrossPack-AVR/bin/avr-gcc -Wall -Os -DF_CPU=$(CLOCK) -mmcu=$(DEVICE) -g -std=c99 -Wl,-u,vfprintf -lprintf_flt -lm |
| 0 | 67 |
| 68 # symbolic targets: | |
| 69 all: main.hex | |
| 70 | |
| 71 .c.o: | |
| 72 $(COMPILE) -c $< -o $@ | |
| 73 | |
| 74 .S.o: | |
| 75 $(COMPILE) -x assembler-with-cpp -c $< -o $@ | |
| 76 # "-x assembler-with-cpp" should not be necessary since this is the default | |
| 77 # file type for the .S (with capital S) extension. However, upper case | |
| 78 # characters are not always preserved on Windows. To ensure WinAVR | |
| 79 # compatibility define the file type manually. | |
| 80 | |
| 81 .c.s: | |
| 82 $(COMPILE) -S $< -o $@ | |
| 83 | |
| 84 flash: all | |
| 20 | 85 $(AVRDUDE) -D -U flash:w:main.hex:i |
| 0 | 86 |
| 87 checkprog: | |
| 88 $(AVRDUDE) -v | |
| 89 | |
| 90 fuse: | |
| 91 $(AVRDUDE) $(FUSES) | |
| 92 | |
| 93 # Xcode uses the Makefile targets "", "clean" and "install" | |
| 94 install: flash | |
| 95 | |
| 96 # if you use a bootloader, change the command below appropriately: | |
| 97 load: all | |
| 98 bootloadHID main.hex | |
| 99 | |
| 100 clean: | |
| 101 rm -f main.hex main.elf $(OBJECTS) | |
| 102 | |
| 103 # file targets: | |
| 104 main.elf: $(SOURCE) | |
| 105 $(COMPILE) -o main.elf $(SOURCE) $(LIBS) | |
| 106 | |
| 107 main.hex: main.elf | |
| 108 rm -f main.hex | |
| 109 avr-objcopy -j .text -j .data -O ihex main.elf main.hex | |
| 110 avr-size --format=avr --mcu=$(DEVICE) main.elf | |
| 111 # If you have an EEPROM section, you must also create a hex file for the | |
| 112 # EEPROM and add it to the "flash" target. | |
| 113 | |
| 114 # Targets for code debugging and analysis: | |
| 115 disasm: main.elf | |
| 116 avr-objdump -d main.elf | |
| 117 | |
| 118 cpp: | |
| 119 $(COMPILE) -E main.c |