Mercurial > templog
annotate Makefile @ 311:fc96a51bdce6
Fix build
| author | Matt Johnston <matt@ucc.asn.au> |
|---|---|
| date | Fri, 11 May 2012 22:12:11 +0800 |
| parents | 0a64532c1de1 |
| children | 9d538f674ff0 |
| rev | line source |
|---|---|
| 306 | 1 # Name: Makefile |
| 2 # Author: <insert your name here> | |
| 3 # Copyright: <insert your copyright message here> | |
| 4 # License: <insert your license reference here> | |
| 5 | |
| 6 # This is a prototype Makefile. Modify it according to your needs. | |
| 7 # You should at least check the settings for | |
| 8 # DEVICE ....... The AVR device you compile for | |
| 9 # CLOCK ........ Target AVR clock rate in Hertz | |
| 10 # OBJECTS ...... The object files created from your source files. This list is | |
| 11 # usually the same as the list of source files with suffix ".o". | |
| 12 # PROGRAMMER ... Options to avrdude which define the hardware you use for | |
| 13 # uploading to the AVR and the interface where this hardware | |
| 14 # is connected. We recommend that you leave it undefined and | |
| 15 # add settings like this to your ~/.avrduderc file: | |
| 16 # default_programmer = "stk500v2" | |
| 17 # default_serial = "avrdoper" | |
| 18 # FUSES ........ Parameters for avrdude to flash the fuses appropriately. | |
| 19 | |
| 308 | 20 DEVICE = atmega328 |
| 21 CLOCK = 1000000 | |
| 306 | 22 PROGRAMMER = #-c stk500v2 -P avrdoper |
|
310
0a64532c1de1
Fill out more main.c structure
Matt Johnston <matt@ucc.asn.au>
parents:
309
diff
changeset
|
23 OBJECTS = main.o ff.o mmc.o onewire.o |
| 306 | 24 FUSES = -U hfuse:w:0xd9:m -U lfuse:w:0x24:m |
| 25 | |
| 26 # ATMega8 fuse bits used above (fuse bits for other devices are different!): | |
| 27 # Example for 8 MHz internal oscillator | |
| 28 # Fuse high byte: | |
| 29 # 0xd9 = 1 1 0 1 1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000) | |
| 30 # ^ ^ ^ ^ ^ ^ ^------ BOOTSZ0 | |
| 31 # | | | | | +-------- BOOTSZ1 | |
| 32 # | | | | +---------- EESAVE (set to 0 to preserve EEPROM over chip erase) | |
| 33 # | | | +-------------- CKOPT (clock option, depends on oscillator type) | |
| 34 # | | +---------------- SPIEN (if set to 1, serial programming is disabled) | |
| 35 # | +------------------ WDTON (if set to 0, watchdog is always on) | |
| 36 # +-------------------- RSTDISBL (if set to 0, RESET pin is disabled) | |
| 37 # Fuse low byte: | |
| 38 # 0x24 = 0 0 1 0 0 1 0 0 | |
| 39 # ^ ^ \ / \--+--/ | |
| 40 # | | | +------- CKSEL 3..0 (8M internal RC) | |
| 41 # | | +--------------- SUT 1..0 (slowly rising power) | |
| 42 # | +------------------ BODEN (if 0, brown-out detector is enabled) | |
| 43 # +-------------------- BODLEVEL (if 0: 4V, if 1: 2.7V) | |
| 44 # | |
| 45 # For computing fuse byte values for other devices and options see | |
| 46 # the fuse bit calculator at http://www.engbedded.com/fusecalc/ | |
| 47 | |
| 48 | |
| 49 # Tune the lines below only if you know what you are doing: | |
| 50 | |
| 51 AVRDUDE = avrdude $(PROGRAMMER) -p $(DEVICE) | |
|
310
0a64532c1de1
Fill out more main.c structure
Matt Johnston <matt@ucc.asn.au>
parents:
309
diff
changeset
|
52 COMPILE = avr-gcc -Wall -Os -DF_CPU=$(CLOCK) -mmcu=$(DEVICE) -g -std=c99 |
| 306 | 53 |
| 54 # symbolic targets: | |
| 55 all: main.hex | |
| 56 | |
| 57 .c.o: | |
| 58 $(COMPILE) -c $< -o $@ | |
| 59 | |
| 60 .S.o: | |
| 61 $(COMPILE) -x assembler-with-cpp -c $< -o $@ | |
| 62 # "-x assembler-with-cpp" should not be necessary since this is the default | |
| 63 # file type for the .S (with capital S) extension. However, upper case | |
| 64 # characters are not always preserved on Windows. To ensure WinAVR | |
| 65 # compatibility define the file type manually. | |
| 66 | |
| 67 .c.s: | |
| 68 $(COMPILE) -S $< -o $@ | |
| 69 | |
| 70 flash: all | |
| 71 $(AVRDUDE) -U flash:w:main.hex:i | |
| 72 | |
| 73 fuse: | |
| 74 $(AVRDUDE) $(FUSES) | |
| 75 | |
| 76 # Xcode uses the Makefile targets "", "clean" and "install" | |
| 77 install: flash fuse | |
| 78 | |
| 79 # if you use a bootloader, change the command below appropriately: | |
| 80 load: all | |
| 81 bootloadHID main.hex | |
| 82 | |
| 83 clean: | |
| 84 rm -f main.hex main.elf $(OBJECTS) | |
| 85 | |
| 86 # file targets: | |
| 87 main.elf: $(OBJECTS) | |
| 88 $(COMPILE) -o main.elf $(OBJECTS) | |
| 89 | |
| 90 main.hex: main.elf | |
| 91 rm -f main.hex | |
| 92 avr-objcopy -j .text -j .data -O ihex main.elf main.hex | |
| 93 avr-size --format=avr --mcu=$(DEVICE) main.elf | |
| 94 # If you have an EEPROM section, you must also create a hex file for the | |
| 95 # EEPROM and add it to the "flash" target. | |
| 96 | |
| 97 # Targets for code debugging and analysis: | |
| 98 disasm: main.elf | |
| 99 avr-objdump -d main.elf | |
| 100 | |
| 101 cpp: | |
| 102 $(COMPILE) -E main.c |