|
4
|
1 #ifndef ONEWIRE_H_ |
|
|
2 #define ONEWIRE_H_ |
|
|
3 |
|
|
4 #ifdef __cplusplus |
|
|
5 extern "C" { |
|
|
6 #endif |
|
|
7 |
|
|
8 #include <stdint.h> |
|
|
9 |
|
|
10 /*******************************************/ |
|
|
11 /* Hardware connection */ |
|
|
12 /*******************************************/ |
|
|
13 |
|
|
14 /* Define OW_ONE_BUS if only one 1-Wire-Bus is used |
|
|
15 in the application -> shorter code. |
|
|
16 If not defined make sure to call ow_set_bus() before using |
|
|
17 a bus. Runtime bus-select increases code size by around 300 |
|
|
18 bytes so use OW_ONE_BUS if possible */ |
|
9
|
19 #define OW_ONE_BUS |
|
4
|
20 |
|
|
21 #ifdef OW_ONE_BUS |
|
|
22 |
|
9
|
23 #define OW_PIN PB1 |
|
|
24 #define OW_IN PINB |
|
|
25 #define OW_OUT PORTB |
|
|
26 #define OW_DDR DDRB |
|
4
|
27 #define OW_CONF_DELAYOFFSET 0 |
|
|
28 |
|
|
29 #else |
|
|
30 #if ( F_CPU < 1843200 ) |
|
|
31 #warning | Experimental multi-bus-mode is not tested for |
|
|
32 #warning | frequencies below 1,84MHz. Use OW_ONE_WIRE or |
|
|
33 #warning | faster clock-source (i.e. internal 2MHz R/C-Osc.). |
|
|
34 #endif |
|
|
35 #define OW_CONF_CYCLESPERACCESS 13 |
|
|
36 #define OW_CONF_DELAYOFFSET ( (uint16_t)( ((OW_CONF_CYCLESPERACCESS) * 1000000L) / F_CPU ) ) |
|
|
37 #endif |
|
|
38 |
|
|
39 // Recovery time (T_Rec) minimum 1usec - increase for long lines |
|
|
40 // 5 usecs is a value give in some Maxim AppNotes |
|
|
41 // 30u secs seem to be reliable for longer lines |
|
|
42 //#define OW_RECOVERY_TIME 5 /* usec */ |
|
|
43 //#define OW_RECOVERY_TIME 300 /* usec */ |
|
|
44 #define OW_RECOVERY_TIME 10 /* usec */ |
|
|
45 |
|
|
46 // Use AVR's internal pull-up resistor instead of external 4,7k resistor. |
|
|
47 // Based on information from Sascha Schade. Experimental but worked in tests |
|
|
48 // with one DS18B20 and one DS18S20 on a rather short bus (60cm), where both |
|
|
49 // sensores have been parasite-powered. |
|
|
50 #define OW_USE_INTERNAL_PULLUP 1 /* 0=external, 1=internal */ |
|
|
51 |
|
|
52 /*******************************************/ |
|
|
53 |
|
|
54 |
|
|
55 #define OW_MATCH_ROM 0x55 |
|
|
56 #define OW_SKIP_ROM 0xCC |
|
|
57 #define OW_SEARCH_ROM 0xF0 |
|
|
58 |
|
|
59 #define OW_SEARCH_FIRST 0xFF // start new search |
|
|
60 #define OW_PRESENCE_ERR 0xFF |
|
|
61 #define OW_DATA_ERR 0xFE |
|
|
62 #define OW_LAST_DEVICE 0x00 // last device found |
|
|
63 |
|
|
64 // rom-code size including CRC |
|
|
65 #define OW_ROMCODE_SIZE 8 |
|
|
66 |
|
|
67 extern uint8_t ow_reset(void); |
|
|
68 |
|
|
69 extern uint8_t ow_bit_io( uint8_t b ); |
|
|
70 extern uint8_t ow_byte_wr( uint8_t b ); |
|
|
71 extern uint8_t ow_byte_rd( void ); |
|
|
72 |
|
|
73 extern uint8_t ow_rom_search( uint8_t diff, uint8_t *id ); |
|
|
74 |
|
|
75 extern void ow_command( uint8_t command, uint8_t *id ); |
|
|
76 extern void ow_command_with_parasite_enable( uint8_t command, uint8_t *id ); |
|
|
77 |
|
|
78 extern void ow_parasite_enable( void ); |
|
|
79 extern void ow_parasite_disable( void ); |
|
|
80 extern uint8_t ow_input_pin_state( void ); |
|
|
81 |
|
|
82 #ifndef OW_ONE_BUS |
|
|
83 extern void ow_set_bus( volatile uint8_t* in, |
|
|
84 volatile uint8_t* out, |
|
|
85 volatile uint8_t* ddr, |
|
|
86 uint8_t pin ); |
|
|
87 #endif |
|
|
88 |
|
|
89 #ifdef __cplusplus |
|
|
90 } |
|
|
91 #endif |
|
|
92 |
|
|
93 #endif |
